The Traditional Methods of Pre-washing Jeans
When we talk about pre-washed jeans and garment finishing, stonewashing is hard to get around. It was this pre-washing method that kickstarted the denim laundering industry, and it’s used in denim laundries all over the world to this day.However, these days, things are a little more complicated. Most washes are created with a combination of several different pre-washing methods, which is known ‘recipes.’
Let’s take a closer look at some of the most common traditional garment finishing methods used to fade and soften jeans.
Rinsing
A rinse is the simplest denim laundry process; the jeans are washed in water. The purpose is to soften the denim and give it that one-wash look. Many Japanese brands sell their jeans rinsed, or one-washed, especially when they’re made from unsanforized denim, in which case the rinse shrinks down the jeans.
If the jeans are going through further washing steps, laundries also ‘desize’ the jeans—that is, remove the sizing agent (starch) to make the denim softer—before other treatments. The rinsing process is also often one of the last steps in the laundry ‘recipe’ with the purpose of washing out and neutralising fading agents.
Stonewashing
Simply put, stonewashing is a laundry process where garments—in this case jeans—are washed with pumice stones. The stones are added to the laundry machine, and the rough surface of the stones abrades the fabric and wears off the indigo dye. The result is a softer touch and washed-down look.
Getting the right stones has not always been easy. Industry veteran, Panos Sofianos recalls how he had to tell a little white lie to his supplier back in the early 80s when he was working in his native Greece:
We needed a source for pumice stones. The best came from a volcanic island called Nisyros. The only supplier there refused to sell more than few kilograms to us because he could not believe we were really looking for material for industrially laundering jeans. We had to lie, saying that the pumice would be used for insulation in ovens.”
Hand Scraping
Hand scraping is a manual garment finishing process that is used to recreate whiskers and honeycombs, as well as general fading on the thighs and the seat area, which you normally get with natural wear and tear. As the name suggests, the scraping is done by hand. And it’s labour-intensive. Trained craftsmen use sandpaper, sanding blocks and other sanding tools to abrade the denim and remove the colour. Sometimes, a mould with all the creases is used. This makes the process quicker, but more expensive as new moulds need to be created for every wash. Craftsmen may also use drills to distress the hems and pocket edges or to create nicks and cuts.
While it may look relatively easy, if you’ve ever tried hand scraping yourself, you know it’s not! What the jeans end up looking like in the end greatly depends on the skills and attention to detail of the craftsman. Hand scraping is also the finishing process that’s often used to create breaks and rips.
Sandblasting
Sandblasting is a garment finishing process where tiny sand grains are blasted onto the jeans under high pressure. It gives a result similar to hand scraping, but it’s faster and less physically exhausting to do. Industry veteran, Martin Schaefer, recalls his first encounter with the method:
I saw it first in 1986 in a French laundry. The raw jeans were lying on a table and the sand was blown onto the jeans. It’s a horribly dusty method, and the workers were wearing masks, but that wasn’t enough.”
Sandblasting has been harshly criticised as the procedure puts workers at severe risk of lung cancer and eventually death when it’s done without proper ventilation and the right safety equipment.
the use of sandblasting increased when the distressed denim trend took off in the 1990s.” The finishing method was banned in 2009 in Turkey when the government discovered that many denim workers were dying! The following year, 40 of the world’s biggest denim brands including, Levi Strauss & Co. and H&M, banned sandblasting to put an end the fatal approach.
Sandblasting is safe when it’s done under controlled circumstances with workers wearing the appropriate protection gear. The problem is that in most places where sandblasting was (and is) used, safety is neglected, to say the least.
Bleaching
As early as the late-1960s, laundries started experimenting with ways to create an overall washed-down look using chemical bleaching agents, such as chlorine. This garment finishing process dramatically brightens the colour of the jeans without abrasion.
Although the result is also an overall fade, bleaching is not comparable to stonewashing, argues denim designer, Stefano Aldighieri. He believes that bleaching is not an alternative to stonewashing. It can, however, accelerate the color loss and thereby expedite the process.”
PP Spraying
Another common chemical used to fade jeans without abrasion is potassium permanganate, often abbreviated ‘PP.’ This liquid chlorine-free oxidising fading agent is used to recreating local fading, just like hand scraping. PP is usually hand-sprayed onto certain areas of the garment, which is mounted on rubber dummies. It can also be applied by hand with a special glove or a paint brush, or even without any manual work using robots.
3D Shaping
The issue with industrially-made whiskers and honeycombs is that they often lack the 3D effect you get when you’ve created them with natural wear. 3D shaping aims to recreate just that.
This manual finishing process replicates the look denim gets when it’s moulded to your body. It’s used both before and after the local fading is done. And you can have both permanent and temporary 3D shaping.
The jeans are usually dipped in or sprayed with starch that makes the denim stiff. Then they’re fitted on a rubber dummy, and the legs are bent like if a person was squatting a little. Workers then manually crinkle the jeans in the places where whiskers and honeycombs would naturally appear. To set the crease in place, the jeans are then baked in a massive industrial oven.
